| Number of inputs and outputs |
Number of digital outputs: 2; Number of analog outputs: 1 |
| Measuring range |
| -1...16 bar | -14.6...232 psi | -0.1...1.6 MPa |
|
| Process connection |
threaded connection G 1 external thread sealing cone Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop. |
| System |
gold-plated contacts |
| Application |
flush mountable for the food and beverage industry |
| Media |
viscous media and liquids with suspended particles; liquids and gases |
| Medium temperature |
-25...150 |
| Min. bursting pressure |
|
| Pressure rating |
|
| Vacuum resistance |
|
| Type of pressure |
relative pressure; vacuum |
| No dead space |
yes |
| MAWP (for applications according to CRN) |
50 |
| Min. insulation resistance |
100; (500 V DC) |
| Protection class |
III |
| Reverse polarity protection |
yes |
| Integrated watchdog |
yes |
| Step response time analog output |
30 |
| Min. response time of switching output (dAP) |
3 |
| Step response time analog output |
7 |
| Number of inputs and outputs |
Number of digital outputs: 2; Number of analog outputs: 1 |
| Total number of outputs |
2 |
| Output signal |
switching signal; analog signal; IO-Link |
| Electrical design |
PNP/NPN |
| Number of digital outputs |
2 |
| Output function |
normally open / closed; (configurable) |
| Number of analog outputs |
1 |
| Analog current output |
4...20, invertible; (scalable) |
| Short-circuit protection |
yes |
| Type of short-circuit protection |
yes (non-latching) |
| Overload protection |
yes |
| Measuring range |
| -1...16 bar | -14.6...232 psi | -0.1...1.6 MPa |
|
| Set point SP |
| -0.98...16 bar | -14.2...232.1 psi | -0.098...1.6 MPa |
|
| Reset point rP |
| -1...15.98 bar | -14.5...231.7 psi | -0.1...1.598 MPa |
|
| Analog start point |
| -1...12.8 bar | -14.5...185.6 psi | -0.1...1.28 MPa |
|
| Analog end point |
| 2.2...16 bar | 31.9...232.1 psi | 0.22...1.6 MPa |
|
| Min. difference between SP and rP |
|
| In steps of |
|
| Factory setting |
| SP1 = 4.00bar | rP1 = 3.68 bar | | SP2 = 12.00 bar | rP2 = 11.68 bar | | ASP = 0.00 bar | AEP = 16.00 bar | | dAP = 0.06 s | dAA = 0.06 s |
|
| Accuracy |
± 2,5+ (0,08 x ( Umgebungstemperatur - Mediumtemperatur )) |
| Repeatability |
± 0,2 |
| Resolution |
0.2 |
| Switch point accuracy |
< ± 0,2; (DIN EN IEC 62828-1; Turn down 1:1) |
| Repeatability |
< ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1) |
| Characteristics deviation |
< ± 0,2; (DIN IEC EN 62828-1 incl. zero point and span error, non-linearity, hysteresis; Turn down 1:1) |
| Linearity deviation |
< ± 0,15; (Turn down 1:1) |
| Hysteresis deviation |
< ± 0,15; (Turn down 1:1) |
| Long-term stability |
< ± 0,1; (Turn down 1:1; per year) |
| Total deviation over temperature range |
| Temperature range | total deviation |
|---|
| -25...15 °C | Characteristics deviation ± 0,05 % of the span / 10 K | | 15...80 °C | Characteristics deviation | | 80...150 °C | Characteristics deviation ± 0,1 % of the span / 10 K |
|
| Notes on the accuracy / deviation |
for further details see section Diagrams and graphs |
| Damping process value dAP |
0...99.99 |
| Damping for the analog output dAA |
0...99.99 |
| Communication interface |
IO-Link |
| Transmission type |
COM2 (38,4 kBaud) |
| IO-Link revision |
1.1 |
| SDCI standard |
IEC 61131-9 |
| Profiles |
| Common - I&D | Identification and Diagnosis | | Function | Measurement data, high resolution |
|
| SIO mode |
yes |
| Required master port class |
A |
| Min. process cycle time |
5.6 |
| IO-Link resolution pressure |
0.0005 |
| IO-Link resolution temperature |
0.2 |
| IO-Link process data (cyclical) |
| Function | bit length |
|---|
| pressure | 32 | | temperature | 32 | | device status | 4 | | binary switching information | 2 |
|
| IO-Link functions (acyclical) |
application specific tag; internal temperature; operating hours counter; switching cycles counter; Pressure peak counter |
| Supported DeviceIDs |
| Type of operation | DeviceID |
|---|
| default | 1147 |
|
| Ambient temperature |
-25...80 |
| Storage temperature |
-40...100 |
| Protection |
IP 67; IP 68; IP 69K |
| EMC |
|
| Shock resistance |
| DIN EN 60068-2-27 | 50 g (11 ms) |
|
| Vibration resistance |
| DIN EN 60068-2-6 | 20 g (10...2000 Hz) |
|
| MTTF |
214 |
| Note on approval |
| Factory certificate available as download at www.factory-certificate.ifm |
|
| UL approval |
| UL approval number | J049 | | File number UL | E174189 |
|
| Weight |
384.7 |
| Housing |
tubular |
| Dimensions |
Ø 50 / L = 106 |
| Material |
stainless steel (1.4404 / 316L); FKM; PTFE; PBT; PEI; PFA |
| Materials (wetted parts) |
ceramics (99.9 % Al2O3); stainless steel (1.4435 / 316L) surface characteristics: Ra < 0,4 µm / Rz = 4 µm; PTFE |
| Min. pressure cycles |
100 million |
| Tightening torque |
20 |
| Process connection |
threaded connection G 1 external thread sealing cone Attention: The unit must only be installed in a process connection for G1 sealing cone.; The G1A sealing cone of the unit is only suited for adapters with metal end stop. |
| Display |
| Display unit | LED, green | | Switching status | LED, yellow | | Function display | alphanumeric display, 4-digit | | Measured values | alphanumeric display, 4-digit |
|
| Display unit |
bar; psi; MPa |
| Pack quantity |
1 pcs. |
| Connection |
Connector: 1 x M12; coding: A; Contacts: gold-plated |
